|
|
|
|
| Vol. | No. | Year | Title | Author |
|---|---|---|---|---|
| Vol. 1 | No. 1 | 1955 | Observation of Bainite Transformation by Hot Stage Microscope | Kazuo Tsuya |
| Vol. 1 | No. 1 | 1955 | Age-Hardening of Titanium-Iron Alloys | Susumu Yoshida,Hidehiko Yoshida,Takashi Araki,Yuko Tsuya |
| Vol. 1 | No. 1 | 1955 | The Microscope Objective (VI) Interferometric Study on Extra-Axial Aberrations | Yukichi Ukita,Jumpei Tsujiuchi |
| Vol. 1 | No. 1 | 1955 | Photoelastic Analysis of Stresses in The Detachable Rock Bit | Shoji Shimamura,Morio Jido |
| Vol. 1 | No. 1 | 1955 | Fundamental Study on Manufacturing Standard Block for Hardness Measurement (III) The Effect of Subzero-Treatment Conditions on the Hardness Distribution | Tesutaro Mitsuhashi,Manabu Ueno,Shin Yokoi |
| Vol. 1 | No. 1 | 1955 | Studies of Non-Destructive Testing (II) On the Dye Penetrant Inspection | Susumu Yoshida,Kiyoshi Tamura |
| Vol. 1 | No. 1 | 1955 | Studies of Non-Destructive Testing (III) On the Electrified Particle Inspection | Susumu Yoshida,Kiyoshi Tamura |
| Vol. 1 | No. 1 | 1955 | Study on High Speed Machining of Metal (II) Measurement of Cutting Force due to Magnetostriction Phenomenon | Hidehiko Takeyama,Eiji Usui |
| Vol. 1 | No. 1 | 1955 | Instrumentation in Cascade Test (II) Automatic Analog Computer for the Energy Loss Coefficient | Kazuto Togino,Hiroshi Honda,Shozo Ito,Yasuo Shimoda |
| Vol. 1 | No. 1 | 1955 | A Presumption of the Cooling Effects of the Turbine Blade on the Gas-Turbine (I) | Joji Yamaga |
| Vol. 1 | No. 1 | 1955 | On the Flow in the Axial Flow Machines (IV) The Experiment on a Cascade of Twisted Blades | Masakazu Harada |
| Vol. 1 | No. 1 | 1955 | On the Calculation of Wire Drawing Force (I) The Case of Conventional Wire Drawing with Work Hardening | Kenichi Nakamura,Hiroo Takahashi,Juzo Kurihara |
| Vol. 1 | No. 1 | 1955 | On the Calculation of Wire Drawing Force (II) The Case of Wire Drawing with Back Tension | Kenichi Nakamura,Hiroo Takahashi |
| Vol. 1 | No. 1 | 1955 | A Study on Low Temperature Brazing (II) Wetting by Droplet Method and Brazing Strength | Hitoshi Ishida,Shiro Yaji |
| Vol. 1 | No. 1 | 1955 | Temperature Distribution During Spot Welding (I) Temperature Distributions at Various Stages of Spot Welding | Sukemitsu Ito |
| Vol. 1 | No. 1 | 1955 | Research on the Surface Treatment of Zinc Die-cast (II) On the Method of Electropolishing | Matsuhei Kishi |
| Vol. 1 | No. 1 | 1955 | On the Trial Manufacturing of Fiuidizing Roaster for Reduction | Tetsutaro Mitsuhashi,Manabu Ueno,Minoru Tanaka |
| Vol. 1 | No. 1 | 1955 | Studies of the Corrosion Resistance of Titanium Alloys (I) Corrosion Resistance of Ti-Al and Ti-Ni Alloys | Susumu Yoshida,Shigetake Okamoto,Takashi Araki |
| Vol. 1 | No. 1 | 1955 | A Study of Ti-Al Alloys (II) The Effects of Addition of Ni on the Properties of Ti-Al Alloys | Susumu Yoshida,Takashi Araki |
| Vol. 1 | No. 2 | 1955 | On the Vibration of Gas Turbine Blades. Wind Tunnel Experiments on the Pure Bending Flutter in Accelerating Cascade | Jumpei Shioiri,Shuji Shibata |
| Vol. 1 | No. 2 | 1955 | The Surface Relief Effect due to Bainite Transformation Observed by Hot Stage Microscope | Kazuo Tsuya,Tetsutaro Mistuhashi |
| Vol. 1 | No. 2 | 1955 | Problems on Precise Measurements of Thin Films (III. IV) I. On Measurement of Films of High Refractive Indices. II. On Heterogeneity of Films. | Yasuhiro Doi,Yasuhiro Ishida |
| Vol. 1 | No. 2 | 1955 | Study on Torque Meter | Shinsaburo Inomata |
| Vol. 1 | No. 2 | 1955 | Investigation of Gas Turbine Combustion Chamber | Katsuro Yamamoto,Junkichiro Dai |
| Vol. 1 | No. 2 | 1955 | On the Vibration of Gas Turbine Blades (III) General Theory of Cascading-Blade-Flutter in Axial Flow Machines | Jumpei Shioiri |
| Vol. 1 | No. 2 | 1955 | On the Profile of Tube Drawing Dies | Shigehiko Yazawa,Kiyoshi Sato |
| Vol. 1 | No. 2 | 1955 | On the Plug-drawing of Steel Tubes | Shigehiko Yazawa |
| Vol. 1 | No. 2 | 1955 | Measurment of Ball Bearing Clearance | Sansaku Aoki,Tatsuo Utsumi,Seijiro Nemoto |
| Vol. 1 | No. 2 | 1955 | Speed Effect on Metal Machining (I) | Hidehiko Takeyama,Terumi Murai,Eiji Usui |
| Vol. 1 | No. 2 | 1955 | On the Decrease of Flexural Rigidity of Beam due to Elastic Clamping | Shin-ichi Suzuki |
| Vol. 1 | No. 2 | 1955 | Studies on Ball Bearing Steel (II) Effect of Some Metallurgical Factors on the Life of Ball Bearings | Manabu Ueno,Tetsutaro Mitsuhashi,Yutaka Nakano |
| Vol. 1 | No. 2 | 1955 | Studies on Ball-Bearing Steel (III) Austenitizing Behaviour of Acid Open Hearth Furnace's Steels,Basic Electric Arc Furnace's Steels and SKF Ball Bearing Steels | Manabu Ueno,Yutaka Nakano |
| Vol. 1 | No. 2 | 1955 | Temperature Distribution During Spot Welding (III) The Case of Considering the Figure and Material Constant of the Electrode | Sukemitu Ito |
| Vol. 2 | No. 1 | 1956 | An Approximate Solution of the Laminar Flow Heat-Transfer on a Rotating Axially Symmetrical Body Surface in a Uniform Incompressible Flow | Joji Yamaga |
| Vol. 2 | No. 1 | 1956 | Electromagnetic Flowmeter | Kazuto Togino,Yasuo Shimoda |
| Vol. 2 | No. 1 | 1956 | On the Characteristics of Bainite Transformation | Kazuo Tsuya |
| Vol. 2 | No. 1 | 1956 | On the Heat Treatment of Ti-Ni Alloys | Takashi Araki |
| Vol. 2 | No. 1 | 1956 | The Velocity Dependence of Friction of Teflon and its Wear Properties | Kiyoshi Matsubara |
| Vol. 2 | No. 1 | 1956 | An Expermental Investigation of the Transonic Wind-Tunnel Test Section (I) Test of Slotted Walls. | Itu Hiraki,Hirosi Hashizume |
| Vol. 2 | No. 1 | 1956 | The Microscope Objective (VII) Interferometric Study of Star Image | Yukichi Ukita,Jumpei Tsujiuchi |
| Vol. 2 | No. 1 | 1956 | Problems on Precise Measurements of Thin Films (V) -On Anisotropy of Films- |
Yasuhiro Doi,Yuzuru Watanabe |
| Vol. 2 | No. 1 | 1956 | On the Magnetizing Roasting of the Ni-Cr Iron Ore by Fluidized Bed | Tetsutaro Mitsuhashi,Manabu Ueno,Minoru Tanaka |
| Vol. 2 | No. 1 | 1956 | On the Impact Value of Polyester Resin Mixed with Glass Fibre in High and Low Temperature | Shin-ichi Suzuki |
| Vol. 2 | No. 1 | 1956 | Study on Properties of Shell-Cast Gray Iron Tensile Test Bar | Tatsuo Tanaka,Toru Watanabe |
| Vol. 2 | No. 1 | 1956 | On the Vibration of Gas Turbine Blades (V) Appendix to General Theory | Jumpei Shioiri |
| Vol. 2 | No. 1 | 1956 | On the Experimental Cold Strip Mill (I) | Kenichi Nakamura,Hiroo Takahashi |
| Vol. 2 | No. 1 | 1956 | On the Decrease of Young's Modulus of Elastic Body with Contact Surface | Shin-ichi Suzuki |
| Vol. 2 | No. 1 | 1956 | Study on the Basic Cupola Practice (III) Basic Cupola-Acid Converter Duplex Process for the Production of Cast Steels | Tatsuo Tanaka,Tomohiko Maruo,Nakataro Hamano |
| Vol. 2 | No. 1 | 1956 | On the Nitriding of Titanium | Susumu Yoshida,Jo Isono |
| Vol. 2 | No. 1 | 1956 | Studies of the Corrosion Resistance of Titanium Alloys (III) Corrosion Resistance of Ti-Cr,Ti-Mn,Ti-Si and Ti-Mo Alloys | Susumu Yoshida,Shigetake Okamoto,Takashi Araki |
| Vol. 2 | No. 2 | 1956 | On the Numerical Calculation of the Response Function | Yukichi Ukita,Jumpei Tsujiuchi |
| Vol. 2 | No. 2 | 1956 | Aerodynamic Research on the Accelerating Cascade (V,VI) -Cascade Tests of the Nozzle Blades- |
Isamu Wada,Kunito Fukazawa |
| Vol. 2 | No. 2 | 1956 | Study on Wear Process of Carbide Tools | Hidehiko Takeyama,Terumi Murai,Eiji Usui |
| Vol. 2 | No. 2 | 1956 | Low Temperature Annealing of Drawn Wire | Kenichi Nkamura,Yohimune Nakamura |
| Vol. 2 | No. 2 | 1956 | On the Clearance of Ball Bearing in Running State. | Sansaku Aoki,Isao Furukawa |
| Vol. 2 | No. 2 | 1956 | Experiments on Wind Tunnel Turbulence | Hideo Nagasu,Kanji Ohashi |
| Vol. 2 | No. 2 | 1956 | Estimation of the Stress Concentration Factors for a Plate with Various V-Notches under Tension | Shoji Shimamura |
| Vol. 2 | No. 2 | 1956 | Researches on Titanium Fasteners (I) Photoelastic Determination of Stress Concentration Factors for the Unified Screw Thread | Itu Hiraki,Shoji Shimamura,Yoshioki Kanae |
| Vol. 2 | No. 2 | 1956 | A Simple Method of Austenite Grain Size Measurement | Tetsutaro Mitsuhashi,Yuzo Hosoi |
| Vol. 2 | No. 2 | 1956 | Measurement of Elongation of Ferrite Grain in Deep Drawing Sheet | Tetsutaro Mitsuhashi,Yuzo Hosoi |
| Vol. 2 | No. 2 | 1956 | The Noise Increase of Ball Bearings | Sansaku Aoki,Tatuo Utumi,Seiziro Nemoto,Kimpei Okano |
| Vol. 2 | No. 2 | 1956 | The Measurement of Periodic Errors in Gear-Hobbing Machines by the Smoked Glass Method | Kiyoshi Shimoda |
| Vol. 2 | No. 2 | 1956 | On the Naturel Frequency of Swept Cantilevered Rectangular Plate | Shin-ichi Suzuki |
| Vol. 2 | No. 2 | 1956 | Power Losses in Automobile Transmission | Toyotaro Saito,Chuji Ikeya |
| Vol. 2 | No. 2 | 1956 | Studies on Ball Bearing Steels (VI) -X-Ray Determination of Retained Austenite by Integrated Intensities- |
Manabu Ueno,Tetsutaro Mitsuhashi,Yutaka Nakano |
| Vol. 2 | No. 2 | 1956 | The Basic Converter Practice Attempting Chromium Removal | Tatsuo Tanaka,Akira Muramatsu,Tomohiko Mruo,Toru Watanabe |
| Vol. 3 | No. 1 | 1957 | Research on Secondary Loss | Masakazu Harada,Sigehito Kinosita |
| Vol. 3 | No. 1 | 1957 | Study on the Jerky Motion of Table by Hydraulic Drive | Hideichi Makino,Hosei Noguchi |
| Vol. 3 | No. 1 | 1957 | Researches on Threaded Connections (I) -The Effect of the Diametrical Clearance between the Male and Female Screw on the Stress Distribution of a Bolted Joint- |
Shoji Shimamura,Yusei Noguchi |
| Vol. 3 | No. 1 | 1957 | Study on Shave-Turning -Cutting with Inclined Straight Edged Tool- |
Masao Kubota,Tamehiro Kotorii,Minorii Kanai |
| Vol. 3 | No. 1 | 1957 | Studies on Ball Bearing Steels (VIII) -Behaviour of the Carbide in Ball Bearing Steels by Electrolytic Isolation- |
Manabu Ueno,Hirooki Nakajima |
| Vol. 3 | No. 1 | 1957 | Study on High Speed Machining (VI) -Cutting Speed Effect Based upon Theory of Tool-Chip Contact Area- |
Hidehiko Takeyama,Eiji Usui |
| Vol. 3 | No. 1 | 1957 | The Microscope Objective (VIII & X) -On the Resolving Power of Microscope Objective- |
Yukichi Ukita,Jumpei Tsujiuchi |
| Vol. 3 | No. 1 | 1957 | The Microscope Objective (IX) -On the Lens Interferometer for Objective Manufacture- |
Yukichi Ukita,Jumpei Tsujiuchi |
| Vol. 3 | No. 1 | 1957 | On the Effect of Cross-Sectional Shape and Load to the Variation of Flexural Rigidity | Shin-ichi Suzuki |
| Vol. 3 | No. 1 | 1957 | Photoelastic Stress Analysis of Loaded Projections with Various Forms of Serrations | Shoji Shimamura |
| Vol. 3 | No. 1 | 1957 | A Sensitive Tool Dynamometer Equipped with Strain Gages | Masanori Honda,Minori Kanai |
| Vol. 3 | No. 1 | 1957 | Study on High Speed Machining (VII) -Analysis of Chip Curl in Two-Dimensional Flow-Type Machining- |
hidehiko Takeyama,Eiji Usui |
| Vol. 3 | No. 1 | 1957 | Influences of Non-Linear Damping on the Car Body Oscillation -Periodic Oscillation- |
Katsumi Hashikura,Tsuyoshi Sugimoto,Hisao Sakurai |
| Vol. 3 | No. 1 | 1957 | Studies on Corrosion Resistance of Titanium Alloys (III) -Corrosion Resistance of Ti-Ag,Ti-Cu,Ti-Fe,Ti-Co,Ti-W and Ti-Sn Alloys- |
Susumu yoshida,Shigetake Okamoto,Takashi Araki |
| Vol. 3 | No. 1 | 1957 | Chemical Polishing of Titanium Alloys | Shigetake Okamoto |
| Vol. 3 | No. 2 | 1957 | Vibration of Pivot Type Ball Bearing | Tatsuo Utsumi,Renzo Kaneko,Junzo Okamoto |
| Vol. 3 | No. 2 | 1957 | Researches on Threaded Connections (II) -The Effect of the Fineness of Thread on the Elastic Concentrated Stress in a Bolt assembled with a Nut in Tension- |
Shoji Shimamura,Yusei Noguchi |
| Vol. 3 | No. 2 | 1957 | Machinability of Metals | Hidehiko Takeyama,Eiji Usui |
| Vol. 3 | No. 2 | 1957 | Researches on The Diffusers -An Experiment of Annulus Diffusers- |
Masakazu Harada,Hideo Nagasu,Shigehito Kinoshita,Kanji Ohasi |
| Vol. 3 | No. 2 | 1957 | An Experimental Investigation of the Transonic Wind-Tunnel Test Section (II) -Tests of Perforated Walls- |
Itu Hiraki,Toshio Shinohara,Hiroshi Hashizume |
| Vol. 3 | No. 2 | 1957 | Study on Density Filter Improving Image-Forming Characteristics (I) -A Filter in Case of Defocused Aberration- | Jumpei Tsujiuchi,Toshiyuki Yoshikawa |
| Vol. 3 | No. 2 | 1957 | Researches on the Diffusers -An Investigation on a Curved Diffuser- |
Sigehito Kinoshita,Masakazu Harada |
| Vol. 3 | No. 2 | 1957 | On the Dynamical Characteristics of Neidhart Rubber Spring | Shigeo Fujimoto |
| Vol. 3 | No. 2 | 1957 | Study on Detecting Devices for the Automatic Positioning of a Jig Boring Machine | Yasuhiro Doi,Shoichi Tanaka,Kajuro Shimizu |
| Vol. 3 | No. 2 | 1957 | On the tilted Radial Ball Bearing | Sansaku Aoki |
| Vol. 3 | No. 2 | 1957 | An Experimental Study on the Static Strength of Perforated Strips and Riveted Joints of Commercially Pure Titanium | Shoji Shimamura,Yusei Noguchi |
| Vol. 3 | No. 2 | 1957 | A Styudy o CrB Cermet | Riitsu Takagi,Kiyoshi Tamura,Yoshio Tamura |
| Vol. 3 | No. 2 | 1957 | Research on Rolling Resistance of Tire | Rokuro Masaki,Yoshimichi Tanida,Chuji Ikeya |
| Vol. 4 | No. 1 | 1958 | On Indentation of Ball (I) -Experiments on Specimens of Finite Dimensions- |
Shigehiko Yazawa,Kiyoshi Sato,Masao Unno,Go Yaguchi |
| Vol. 4 | No. 1 | 1958 | A Photo-Elastic Analysis of Machining Stresses on Rake Face | Eiji Usui,Hidehiko Takeyama |
| Vol. 4 | No. 1 | 1958 | Severe Wear of Pearlitic Steel Weld Metal | Sukemitu Ito.Kozo Honda,Kikuzo Ishiyama |
| Vol. 4 | No. 1 | 1958 | On the Tilted Radial Ball Bearing (III) | Sansaku Aoki |
| Vol. 4 | No. 1 | 1958 | On the Operating Condition of Automobile Shock Absorber | Katsumi Hashikura,Tsuyoshi Sugimoto,Hiroshi Kuriyama,Hisao Sakurai |
| Vol. 4 | No. 1 | 1958 | Wind Tunnel Measurements of the Drags of Small Spheres at High Speeds | Masayuki Ikui,Yasuharu Nakamura,Ryoji Tarutani,Akihiro Okumura,Syoei Yamagishi |
| Vol. 4 | No. 1 | 1958 | On the Eletronic Type Vibration Level Sorter | Tsuyoshi Sugimoto |
| Vol. 4 | No. 1 | 1958 | The Coefficient of Dry Friction of Metals | Riitsu Takagi,Yuko Tsuya |
| Vol. 4 | No. 1 | 1958 | The Influences of the Condenser's Aberration on the Microscope Images | Jumpei Tsujiuchi,Toshiyuki Yoshikawa |
| Vol. 4 | No. 1 | 1958 | On Indentation Hardness Testing (I) | Shigehiko Yazawa,Masao Unno,Shigeru Yamamoto,Iwakichi Sawano |
| Vol. 4 | No. 1 | 1958 | Research on Rolling Resistance of Tire (II) -Curvature of Running Road and Rolling Resistance of Tire- |
Rokuro Masaki,Yoshimichi Tanida,Chuji Ikeya,Iku Harada |
| Vol. 4 | No. 1 | 1958 | The Loading Characteristics of Tire Used for Automobile Under Dynamic Condition | Shigeo Fujimoto |
| Vol. 4 | No. 1 | 1958 | A Telemetering of Auto Car Speed | Kiyoshi Naka,Iwao Ishii |
| Vol. 4 | No. 2 | 1958 | Wear of Carbon Steel Weld Metal (I) -Microscopical Observations of the Structural Changed Layers of the Worn Surface- |
Sukemitu Iot,Kozo Honda,Kikuzo Ishiyama |
| Vol. 4 | No. 2 | 1958 | Indentation Hardness Testing on Copper | Shigehiko Yazawa,Masao Unno,Go Yaguchi,Iwakichi Sawano |
| Vol. 4 | No. 2 | 1958 | Analysis of Electronic Servo-system Adapted to Numerically Controlled Machine Tool (I) | kazuto Togino |
| Vol. 4 | No. 2 | 1958 | The Friction and Wear of Filled Teflon | Kiyoshi Matsubara |
| Vol. 4 | No. 2 | 1958 | Some Experimental Results on Two-Dimensional Supersonic Nozzle Designed for Mach Number 1・56 | Masayuki Ikui,Yasuharu Nakamura,Ryozi Tarutani,Akira Mituya,Akihiro Okumura |
| Vol. 4 | No. 2 | 1958 | Apparatus for Detecting of Faint Stain on Optical Glass Surface | Yasuhiro Doi,Yasuhiro Ishida |
| Vol. 4 | No. 2 | 1958 | Staining of Polished Optical Glass Surfaces in Various Atmospheres | Yasuhiro Ishida,Yasuhiro Doi |
| Vol. 4 | No. 2 | 1958 | The Effect of the Mean Stress on the Flexural Fatigue Properties of Titanium Sheet Specimens with a Central Hole | Shoji Shimamura,Tetsuo Suda,Keinosuke Ooshima,Yoshitane Shindo |
| Vol. 4 | No. 2 | 1958 | Study on Detecting Devices for the Automatic Positioning of a Jig Boring Machine (II) | Yasuhiro Doi,Shoichi Tanaka,Kajuro Shimizu |
| Vol. 4 | No. 2 | 1958 | Effect of Tool-Grinding Conditions on Machining Performances | Hidehiko Takeyama,Eiji Usui |
| Vol. 4 | No. 2 | 1958 | Some Theoretical and Experimental Analyses on the Rectanguler Frame Type Load Cell for Strain Gage Balances in the Wind Tunnel Testing | Shoji Shimamura,Yusei Noguchi,Yoshitane Shindo |
| Vol. 4 | No. 2 | 1958 | Cornering Characteristics of Automobile Tires (I) | Rokuro Masaki,Toyotaro Saito,Chuji Ikeya,Iku Harada |
| Vol. 5 | No. 1 | 1959 | Transport Theory of Particle Clouds Moving with a Fluid Flow and Undergoing Property Changes (I) | Kazuyoshi Fukusawa |
| Vol. 5 | No. 1 | 1959 | Sur la Correction Differentielle des Coefficients des Aberrations du Troisieme Ordre | Teruhiko Takahashi |
| Vol. 5 | No. 1 | 1959 | One the Indentation of a Ball (II) -Strain Figures Developed in and on the Ball Indentation Specimen- |
Shigehiko Yazawa,kiyoshi Sato,Masao Unno,Go Yaguchi |
| Vol. 5 | No. 1 | 1959 | Wear of Carbon Steel Weld Metal (II) -The Effect of Previous Heat Treatment of the Specimen upon the Wear and the Structural Changed Layers of the Worn Surface- |
Sukumitsu Ito,Kozo Honda,Kikuzo Ishiyama |
| Vol. 5 | No. 1 | 1959 | Wear of Carbon Steel Weld Metal (III) -The Effect of the Rubbing Conditions upon the Wear and the Structural Changed Layers of the Worn Surface- |
Sukimitsu Ito,kikuzo Ishiyama |
| Vol. 5 | No. 1 | 1959 | Some Experiments on the Cold Strip Rolling | Hiroo Takahashi,Satoshi Miyoshi |
| Vol. 5 | No. 1 | 1959 | Wear of Ni-Cr Austenitic Steel Weld Metal (I) -A Study on the Wear and the Structural Changed Layer of the Worn Surface- |
Sukemitsu Ito,Kozo Honda |
| Vol. 5 | No. 1 | 1959 | An Experimental Study on the Abrasion of Martensitic Steel Weld Metal | Sukuemitsu Ito,Mituhiro Kawaguchi |
| Vol. 5 | No. 1 | 1959 | On the Effect of a Structure of 2･5% Al-Mg Alloy on the Micro-Indentation Hardness | Toshio Yoshino |
| Vol. 5 | No. 1 | 1959 | Researches on the Diffusers -A New Design Rule- |
Masakazu Harada |
| Vol. 5 | No. 1 | 1959 | Analysis of Electronic Servosystem Adapted to Numerically Controlled Machine Tool (II) -An Theoretical Analysis of Dynamic Characteristics of D. C. Shunt Servomotor Driven by Grid Controlled Thyratron Amplifier- |
Kazuto Togino |
| Vol. 5 | No. 1 | 1959 | Pulse-Distributor with Parametron for Numerically Controlled Machine Tools | Kazuto Togino,Akira Takahashi |
| Vol. 5 | No. 1 | 1959 | Digital Phase Modulation in Numerically Controlled Machine Tools | Seigo Sajiki,Shozo Ito |
| Vol. 5 | No. 1 | 1959 | Effect of Tire Inflation Pressure on the Automobile Vibration - Statical Control System of Inflation Pressure- |
Shigeo Fujimoto,Hisao Sakurai |
| Vol. 5 | No. 1 | 1959 | On Growth of Stains for Optical Glasses in Acid Solution | Shingo Tsunekane,Yasuhiro Doi |
| Vol. 5 | No. 2 | 1959 | A Digital-to-Analogue Converter and Its Applications (I) | Teiichi Tsuboi |
| Vol. 5 | No. 2 | 1959 | On the Optical Constants of the Black Paints | Yasuhiro Doi,Shingo Tsunerane,Teruhiko Takahashi |
| Vol. 5 | No. 2 | 1959 | Study on Stretch Forming Method of Sheet Metal -Distribution of Circumferential Stress over a Cross Section when the Sheet Metal is Bent under a Constant Tension- |
Hiroshi Kaga,Shiro Yaji |
| Vol. 5 | No. 2 | 1959 | Researches on Titanium Fasteners (II) -Fatigue Strength of Home-Produced Aircraft Bolts and Nuts- |
Shoji Shimamura,Yoshioki Kanae |
| Vol. 5 | No. 2 | 1959 | Research on the Dynamic Rigidity of Machine Tools (I) -On the Apparatus for Measuring Natural Frequencies of Vibration of Machine Tools- |
Masanori Honda,Takeshi Yasui |
| Vol. 5 | No. 2 | 1959 | Low Speed Characteristics of Swept-back Wings | Masayuki Ikui,Nobukatsu Han,Yasuharu Nakamura,Ryoji Tarutani,Noboru Hashimoto,Akira Mitsuya |
| Vol. 5 | No. 2 | 1959 | On the Air Dryer of the Transonic Wind-tunnel | Masayuki Ikui,Yasuharu Nakamura,Ryoji Tarutani,Akira Mitsuya,Akihiro Okumura |
| Vol. 5 | No. 2 | 1959 | On the Laminar Flow Heat Transfer with Heat Sources in the Flow (I) | Joji Yamaga |
| Vol. 5 | No. 2 | 1959 | Analysis of Electronic Servomotor Adapted to Numerically Controlled Machine Tool (V) -Experimental Analysis of Dynamic Characteristics of D. C. Shunt Servomotor Driven by Grid-Controlled Thyratron Amplifier- |
Kazuto Togino,Takashi Endo |
| Vol. 5 | No. 2 | 1959 | Analysis of Electronic Servosystem Adapted to Numerically Controlled Machine Tool (III, IV) -A Theoretical Analysis of Dynamic Characteristics of D. C. Shunt Servomotor Driven by Grid-Controlled Thyratron Amplifier- |
Kazuto Togino |
| Vol. 5 | No. 2 | 1959 | Research on Rolling Resistance of Tire (III) -Empirical Investigation on Rolling Resistance of Tire- |
Rokuro Masaki,Toyotaro Saito,Chuji Ikeya,Iku Harada |
| Vol. 5 | No. 2 | 1959 | Cornering Characteristics of Automobile Tires (II) | Rokuro Masaki,Toyotaro Saito,Chuji Ikeya,Iku Harada |
| Vol. 5 | No. 2 | 1959 | Investigation on Tube-Expanding Practice (I) -Effect of Clearance on Tube-Expanding Practice of Steel Tube- |
Tomohiko Maruo,Hiroshi Ito |
| Vol. 6 | No. 1 | 1960 | On Measurement of Small Quantity of Gas Flow by Primitive Venturi-Tubo | Kazuyoshi Fukusawa,Mitsuyoshi Iguchi |
| Vol. 6 | No. 1 | 1960 | A Digital-to-Analogue Converter and Its Applications (II) | Teiichi Tsuboi |
| Vol. 6 | No. 1 | 1960 | On the Visibility of Moire Fringe | Kajuro Shimizu,Yasuhiro Doi |
| Vol. 6 | No. 1 | 1960 | Steady and Unsteady Characteristics of Fans and Blowers | Masakazu Harada |
| Vol. 6 | No. 1 | 1960 | On the New Bearing Liner -For the Lauson H-2 Oil Test Engine- |
Takeshi Ishii,Isamu Shimada |
| Vol. 6 | No. 1 | 1960 | The Car Body Roll Caused by Steering Operation and Roll Control System | Katsumi Hashikura,Tsuyoshi Sugimoto,Hiroshi kuriyama |
| Vol. 6 | No. 1 | 1960 | An Approximate Calculation of the Laminar Skin-friction and Heat-transfer on a Rotating Axially Symmetrical Body Surface in a Uniform Flow | Joji Yamaga |
| Vol. 6 | No. 1 | 1960 | On the Laminar Flow Heat Transfer with Heat Sources in the Flow (II) | Joji Yamaga |
| Vol. 6 | No. 1 | 1960 | The Lateral Stiffness of Automobile Tire | Sigeo Fujimoto,Hisao Sakurai |
| Vol. 6 | No. 1 | 1960 | On Fatigue Properties of Plastics Materials (I) -Effect of Environmental Temperature on Flexural Fatigue Strength of a Polyester Glass-Mat Laminate- |
Shoji Shimamura |
| Vol. 6 | No. 2 | 1960 | A Digital-to-Analogue Converter and Its Applications (III) (Appendix) New Approximate Fractional Expressions for tanθ | Teiichi Tsuboi |
| Vol. 6 | No. 2 | 1960 | Polarimetric Study on Thin Films (Part I) | Yasuhiro Doi |
| Vol. 6 | No. 2 | 1960 | Polarimetric Study on Thin Films (Part II) | Yasuhiro Doi,Shingo Tsunekane |
| Vol. 6 | No. 2 | 1960 | Some Experiments on the Ion Gap Type Combustion Analyser | Munenobu Tanaka,Kin-ichi Motohashi,Katsuji Koinuma |
| Vol. 6 | No. 2 | 1960 | Research of the Rolling Guide Way -About the Lindner Type Model- |
Tatsuo Utsumi,Kiyoshi Fujita |
| Vol. 6 | No. 2 | 1960 | An Analysis of Electronic Servomechanisms with Thyratron Amplifier,Operating as Sampled-Date System (I) | Kazuto Togino,Takashi Endo |
| Vol. 6 | No. 2 | 1960 | Study on Mixing of Different Kind Gases (I) -On Methods of Quantiative Optical Measurement- |
Kazuyoshi Fukusawa |
| Vol. 6 | No. 2 | 1960 | On the Heat-transfer from Rotating Disk Normal to a Uniform Flow (I) | Joji Yamaga |
| Vol. 7 | No. 1 | 1961 | Study on Shave-Truning (II) -Surface Roughness by Carbide Tools- |
Masao Kubota,Minori Kanai,Tamehiro Kotorii |
| Vol. 7 | No. 1 | 1961 | Study on Shave-Turning (III) -Life of High-Speed Steel Tools- |
Masao Kubota,Minori Kanai,Yuhei Masuyama |
| Vol. 7 | No. 1 | 1961 | Study on Shave-Turning (IV) -Life of Carbide Tools- |
Masao Kubota,Minori Kanai,Yuhei Masuyama |
| Vol. 7 | No. 1 | 1961 | Study on Shave-Turning (V) -On the Cutting Temperature- |
Masao Kubota,Minori Kanai,Masuo Kakishima,Hideyo Ito |
| Vol. 7 | No. 1 | 1961 | The Influence of Cold Rolling Process on the Frictional Characteristics of Mild Steel | Kenichi Nakamura,Susumu Aono |
| Vol. 7 | No. 1 | 1961 | An Improved Apparatus for Measuring Friction and Wear | Kiyoshi Matsubara,Makoto Watabane |
| Vol. 7 | No. 1 | 1961 | Vacuum-Driven Transonic Wind-Tunnel at The Government Mechanical Laboratory | Masayuki Ikui,Itsu Hiraki,Yasuharu Nakamura |
| Vol. 7 | No. 1 | 1961 | Local Heat-Transfer Coefficient Measurement by Transient Surface Thermometer Technique | Joji Yamaga,Toshio Ono,Morio Jido,Hiromitsu Futagami |
| Vol. 7 | No. 1 | 1961 | On the Life of the Grinding Wheel -The Research on Establishment of Standards for Working by Metal Grinding- |
Hideichi Makino,Shozo Suzuki,Hosei Noguchi |
| Vol. 7 | No. 1 | 1961 | Cornering Characteristics of Automobile Tires (III) | Toyotaro Saito,Chuji Ikeya |
| Vol. 7 | No. 1 | 1961 | Cornering Characteristics of Automobile Tires (IV) | Toyotaro Saito,Chuji Ikeya |
| Vol. 7 | No. 1 | 1961 | On the Measuring Apparatus of the Rear Axle Power of Automobile | Rokuro Masaki,Iku Harada |
| Vol. 7 | No. 2 | 1961 | Study on Electromagnetic Gas Sampling Valve -For Measuring Scavenging Efficiency in High-Speed Two-Stroke Engines- |
Tsuyoshi Asanuma,Shigeru Yanagihara |
| Vol. 7 | No. 2 | 1961 | On the Stain of Optical Glasses Produced by Acid Corrosion (II) -With the Corrosion of SF Glasses- |
Shngo Tunekane,Yasuhiro Doi |
| Vol. 7 | No. 2 | 1961 | On Fatigue Properties of Plastics Materials (II) -Fatigue Properties of Polyester/Glass Lamiates- |
Shoji Shimamura |
| Vol. 7 | No. 2 | 1961 | Weathering Properties of a Polyester/Glass-Cloth Laminate Under Stress | Shoji Shimamura |
| Vol. 7 | No. 2 | 1961 | Study on Stretch Forming Method of Sheet Metal (II) -Spring-back of Sheet Metal When Bent under a Constant Tension and Subsequently Stretched- |
Hiroshi Kaga,Shiro Yaji |
| Vol. 7 | No. 2 | 1961 | Temperature Dependence of Tool Wear | Hidehiko Takeyama,Ryoji Murata,Shin-ichi Miyazawa |
| Vol. 7 | No. 2 | 1961 | Performances of Carbide Tools in Machining 18-8Stainless Steel | Hidehiko Takeyama |
| Vol. 7 | No. 2 | 1961 | Study on Tool Wear and Tool Life Test by Means of Radioisotopes | Eiji Usui,Yukitaka Nagano,Shin-ichi Miyazawa,Takeshi Furusawa,Hidehiko Takeyama,Riitsu Takagi |
| Vol. 7 | No. 2 | 1961 | An Investigation on Tube-Expanding (II) -Effects of the Degree of Expansion in Steel Tube Expanding- |
Tomohiko Maruo,Hiroshi Ito,Nobuo Terada |
| Vol. 7 | No. 2 | 1961 | Study on the Friction and the Lubrication in Wire Drawing (I) -The Friction in Wire Drawing- |
Kenichi Nkamura,Juzo Kurihara |
| Vol. 7 | No. 2 | 1961 | Study on the Friction and the Lubrication in Wire Drawing (II) -Lubricants for Carbon Steel Wire in Wet Drawing Process- |
Kenichi Nkamura,Juzo Kurihara |
| Vol. 7 | No. 2 | 1961 | On the Shaving of Gears (I) -Shaving of Eccentrically Cut Gears- |
Masataka Senba,Hirofumi Kotorii |
| Vol. 7 | No. 2 | 1961 | Measurement of Blanking Tool Wear by means of Radioisotope | Riitsu Takagi,Tsuyoshi Furusawa,Kimio Tamura,Yoshiaki Matsumoto |
| Vol. 7 | No. 2 | 1961 | Study on the Leveling of Metal Strip -Roller Leveling- |
Choichiro Soda,Keinosuke Oshima |
| Vol. 7 | No. 2 | 1961 | On the Approximate Solution for the Steady-State Response of the Bellows Type Air Spring System with the Reservoir Tank | Shigeo Fujimoto,Hisao Sakurai |
| Vol. 8 | No. 1 | 1962 | On the Optimum Condition of the Metal Grinding | Hideichi Makino,Hosei Noguchi,Shozo Suzuki,Takashi Mizushima,Tetsuya Suto,Koichi Kmakura,Hideo Inoue |
| Vol. 8 | No. 1 | 1962 | Study on Honing (I) -Honing Conditions and Stone Performances- |
Kazutaka Tamakohri,Terumi Murai,Hidehiko Takeyama |
| Vol. 8 | No. 1 | 1962 | On Precision Grinding of Optical Glass | Yasuhiro Ishida,Genji Ogawa |
| Vol. 8 | No. 1 | 1962 | A Method of Strain Measurement on the Inner Surface of High-Pressure Vessels | Hideaki Kudo,Tatsuo Nakane |
| Vol. 8 | No. 1 | 1962 | Electro-hydraulic Servovalve -Position Feedback Type- |
Seigo Sajiki,Makoto Kimura,Osamu Soda |
| Vol. 8 | No. 1 | 1962 | On Optical Measurements of Natural Convection along Vertical Cylinder | Kazuyoshi Fukusawa,Mitsuyoshi Iguchi |
| Vol. 8 | No. 1 | 1962 | Low Speed Characteristics of Swept-Forward, M-and W-planform Wings and Delta Wings | Masakazu Harada,Ryoji Tarutani,Kazuo Komaki,Shunzo Hamada |
| Vol. 8 | No. 1 | 1962 | Friction and Wear Properties of a P. T. F. E.-Impregnated Material | Kiyoshi Matsubara |
| Vol. 8 | No. 1 | 1962 | Study on Drilling (I) -Cutting Forces in Drilling- |
Shuzo Nishida,Shotaro Ozaki,Takashi Motomura |
| Vol. 8 | No. 1 | 1962 | Study on Drilling (II) -Lip Temperature- |
Shuzo Nishida,Shotaro Ozaki,Satoshi Nakayama,Teiju Shiraishi Keiji Nagura |
| Vol. 8 | No. 2 | 1962 | Study on Vibroshaving | Masayuki Yokai |
| Vol. 8 | No. 2 | 1962 | Some Experiments of the Unsteady Vivrations in the Transonic Region -The Investigation on the Aileron Buzz (I)- |
Yoshiaki Hara,Toshinori Ogawa |
| Vol. 8 | No. 2 | 1962 | Frictional Properties of Irradiated Linear Polymers | Kiyoshi Matsubara,Makoto Watanabe |
| Vol. 8 | No. 2 | 1962 | High Speed Interference Calibrator of Standard Scales (I) | Yasuhiro Doi,Kajuro Shimizu,Teiichi Tsuboi,Tsuguo Kouno |
| Vol. 8 | No. 2 | 1962 | Study o Bearing Wear in Engine with Activation Technique | Riitsu Takagi,Takeshi Ishii,Takeshi Furusawa,Isamu Shimada |
| Vol. 8 | No. 2 | 1962 | Study on the Noise of Gears (I) -On the Testing Machine for Noise of Gears- |
Isamu Yuruzume,Takezi Tubuku |
| Vol. 8 | No. 2 | 1962 | Cutting Small Disks from Glass Plates by a Diamond Wheel | Yasuhiro Ishida,Genji Ogawa,Yasuo Takahashi |
| Vol. 8 | No. 2 | 1962 | Study on Traffic Control System -Mathematical Model and Simulator- |
Kazuto Togino,Shotaro Ozaki,Takashi Endo |
| Vol. 8 | No. 2 | 1962 | Research on the Rolling Resistance of Tires (IV) -The Measurement of Deflection and Inflation Pressure of a Tire Rolling on the Road- |
Rokuro Masaki,Iku Harada,Tetsuro Gotanda |
| Vol. 8 | No. 2 | 1962 | The Control System for Car Body Roll | Tsuyoshi Sugimoto,Hisao Sakurai |
| Vol. 9 | No. 1 | 1963 | Researches on Electrolytic Machining Process (I) -Machining under Constant Feed- |
Sukemitsu Ito.Kozo Honda |
| Vol. 9 | No. 1 | 1963 | Proper Mode of Pitching Vibration of Automobile Body | Hiroshi Kuriyama |
| Vol. 9 | No. 1 | 1963 | A Study of Nonlinear Systems with Analog-Digital and Digital-Analog Converter | Kazuto Togino,Kuniko Inoue |
| Vol. 9 | No. 1 | 1963 | On Description for Automatic Programming of Cutting Process | Akira Takahashi |
| Vol. 9 | No. 1 | 1963 | Study on Drilling (III) -On the Effects of Cutting Fluids in Drilling- |
Shotaro Ozaki,Satoshi Nakayama,Teiju Shiraishi,Keiji Nagura |
| Vol. 9 | No. 1 | 1963 | Multicomponent Distillation Column Simulated on Digital Computer | Kazuto Togino,Kuniko Inoue,Kiyoshi Uwagawa,Yoiti Suzuki |
| Vol. 9 | No. 2 | 1963 | The Combined Influence of Hall Effect, Ion Slip and Viscosity on MHD Devices | Tetsuo Yamanishi |
| Vol. 9 | No. 2 | 1963 | Establishment of Machining Standards | Hidehiko Takeyama,Tsutomu Yato,Umetaro Kasuya |
| Vol. 9 | No. 2 | 1963 | Researches on Electrolytic Machining Process (II) -Polarization Curves in Sodium Chloride Solution- |
Sukemitsu Ito,Kunio Chikamori |
| Vol. 9 | No. 2 | 1963 | Study on Honing (II) -Honing Conditions and Stone Performance, for the Case of Mild Steel- |
Terumi Murai,Kazutaka Tamakohri,Tsuguya Sakashita,Hidehiko Takeyama |
| Vol. 9 | No. 2 | 1963 | The Spectral Analysis of Vertical Vibrations of the Sprung Mass System of Vehicles (I) | Hiroshi Kuriyama |
| Vol. 9 | No. 2 | 1963 | A Parametron Circuit for Vehicle Detection (I) | Shuntetsu Matsumoto |
| Vol. 10 | No. 1 | 1964 | On the Electrified Lubrication Method (I) | Kenichi Nakamura,Susumu Aono,Juzo Kurihara |
| Vol. 10 | No. 1 | 1964 | Researches on Electrolytic Machining Process (III) -Corrosion of Mild Steel in Sodium Chloride Solution- |
Sukemitsu Ito,Kunio Chikamori |
| Vol. 10 | No. 1 | 1964 | On Delay Starter with a Top | Tsuneji Yada |
| Vol. 10 | No. 1 | 1964 | Frictional Properties of Irradiated Polymers at Elevated Temperatures | Kiyoshi Matsubara,Makoto Watanabe |
| Vol. 10 | No. 1 | 1964 | The Wear of Porous Chromium Plating under Unlubricated Conditions | Takeshi Furusawa,Matsuhei Kishi,Riitsu Takagi,Go Yaguchi,Torao Nakajo |
| Vol. 10 | No. 1 | 1964 | Vehicle Control System using Parametron | Shuntetsu Matsumoto |
| Vol. 10 | No. 1 | 1964 | The Universal Decision Element with Fluid Type of Logics | Kzsuto Togino,Kuniko Inoue |
| Vol. 10 | No. 1 | 1964 | Study on the Load-Carrying Capacity of Gears (I) -On Pitting and Pitting-Test of Spur Gears- |
Jun Takada |
| Vol. 10 | No. 1 | 1964 | Evaluation of Mean Travel Time in Traffic Flow with Turning Vehicles at Signalized Intersections | Kazuto Togino,Shotaro Ozaki,Takashi Endo,Chizuko Umezawa |
| Vol. 10 | No. 2 | 1964 | Study on Electrolytic Machining Process (IV) -Observations of Lissajous' Figures for Current and Voltage Between Electrodes- |
Sukemitsu Ito,Kunio Chikamori,Toshio Hayashi |
| Vol. 10 | No. 2 | 1964 | Study on Electrolytic Machining Process (V) -Machining by a Pulse Current Similar to Square Wave- |
Sukemitsu Ito,Kozo Honda,Toshio Hayashi |
| Vol. 10 | No. 2 | 1964 | Determination of Scavenging Efficiency in a Swirl Chamber Type Two-Stroke Diesel Engine Using Electromagnetic Gas Sampling Valves | Shigeru Yanagihara,Seishiro Shinohara |
| Vol. 10 | No. 2 | 1964 | Speed Controller in Consideration of Comfort Ride | Makoto Kimura,Minoru Hayase |
| Vol. 10 | No. 2 | 1964 | Study on the Effect of the Lubricating Oil Additives for the Machine Tool Slideways | Murao Mitsui,Hideo Ichikawa,Kazuaki Okada |
| Vol. 10 | No. 2 | 1964 | High Speed Polishing of Optical Glass | Yasuhiro Ishida |
| Vol. 10 | No. 2 | 1964 | A Proposal of Temperature Measuring Method for Gas in Internal Combustion Engine | Joji Yamaga |
| Vol. 10 | No. 2 | 1964 | Turbulent Mixing in Two-Dimensional Flow of Jets I. The Case in which Jets are the same Fluid as Ambient Flow used | Kazuyoshi Fukusawa |
| Vol. 10 | No. 2 | 1964 | A Parametron Circuit for Vehicle Detection (II) | Shuntetsu Matsumoto |
| Vol. 10 | No. 2 | 1964 | Study on Fluid Logic Elements (I) -Fluid Oscillator without Moving Parts- |
Shotaro Ozaki,Yoshiaki Hara |
| Vol. 11 | No. 1 | 1965 | The Frequency Response of Pneumatic Signal Transmission Pipes (I) -Pipes with Uniform Inner Diameters- |
Ryoji Trutani,Sunji Kawamura |
| Vol. 11 | No. 1 | 1965 | Study on Electrolytic Machining Process (VI) -Flow of Electrolyte in a Double-disk Nozzle- |
Sukemitsu Ito,Kunio Chikamori,Akira Kogure,Tatsuya Mori |
| Vol. 11 | No. 1 | 1965 | A Study on the Rigidity of Machine Tools | Masanori Honda,Takeshi Yasui |
| Vol. 11 | No. 1 | 1965 | A Parametron Circuit for Vehicle Detection (III) | Shuntetsu Matsumoto |
| Vol. 11 | No. 1 | 1965 | Experimental Study on Air Lubrication (I) -Suspension of Loads by Air-cushion Effects- |
Toyoki Orita |
| Vol. 11 | No. 1 | 1965 | On Scoring of Gears (I) | Jun Takada,Yoshio Suzuki |
| Vol. 11 | No. 1 | 1965 | Study on the Sintered Carbide Hob (I) -Cutting Test with Fly-tools- |
Akio Fujikawa,Yuji Maeda,Fujio Honda |
| Vol. 11 | No. 1 | 1965 | A Design Method of Traffic Signal System on the Main Street | Shotaro Ozaki,Chizuko Umezawa |
| Vol. 11 | No. 2 | 1965 | The Magnetohydrodynamic Slider Bearing | Hiomasa Saeki |
| Vol. 11 | No. 2 | 1965 | Approximate Solutions for Vibrations of Pretwisted Blades | Masayuki Ikui |
| Vol. 11 | No. 2 | 1965 | Study on Electrolytic Machining Process (VII) -The Effects of the Change of Work Material on the Surface Finish of Products Machined by Direct Current- |
Sukemitsu Ito,Kozo Honda,Fusaji Sakurai |
| Vol. 11 | No. 2 | 1965 | Study on Electrolytic Machining Process (VIII) -Frow of Electrolyte from a Slit Nozzle- |
Sukemitsu Ito,Kunio Chikamori,Fusaji Sakurai |
| Vol. 11 | No. 2 | 1965 | A New Method for Measuring Velocity and Accerelation of Gas Flow | Joji Yamaga,Shuji Shibata |
| Vol. 11 | No. 2 | 1965 | An Analysis of the Annular Flow of Electric Fluids | Kazuyoshi Fukuzawa,Shunsuke Kishimoto |
| Vol. 11 | No. 2 | 1965 | Flow Velocity Effect on Acoustical Insertion Loss of Exhaust Tube System | Shigeo Fujimoto,Hisao Sakurai |
| Vol. 11 | No. 2 | 1965 | Insertion Loss of Acoustic Filter I Exhaust Tube System with Temperature Gradient | Shigeo Fujimoto,Hisao Sakurai |
| Vol. 11 | No. 2 | 1965 | Study on Fluid Logic Elements (II) -Fundamental Design Data for And-Or Elements- |
Shotaro Ozaki,Yoshiaki Hara |
| Vol. 12 | No. 1 | 1966 | Effect of Hot-Surface on Combustion of Injection Fuels | Naohisa Teshirogi,Yoshitada Uchiyama,Kin-ichi Motohashi |
| Vol. 12 | No. 1 | 1966 | Investigations on Externally Pressurized Air Journal Bearings (I) -Static State Bearing without Pocket- |
Masakazu Harada,Toshinori Ogawa |
| Vol. 12 | No. 1 | 1966 | An Experimental Investigation of the Grinding Process | Hideichi Makino,Tetsuya Suto,Eiichi Fukushima |
| Vol. 12 | No. 1 | 1966 | Research on the Dynamic Rigidity of Machine Tools (X) -Natural Vibration of Double Column Type Boring Machines- |
Takeshi Yasui,Norimitsu Ozawa |
| Vol. 12 | No. 2 | 1966 | Study on Electrolytic Machining Process (IX) -Effect of Inhibitor in Sodium Chloride Solution on the Surface Finish of Work Machined by Direct Current- |
Sukemitsu Ito,Nobuo Shikata |
| Vol. 12 | No. 2 | 1966 | Study on Electrolytic Machining Process (X) -Flow of Electrolyte Mixed with Gas- |
Sukemitsu Ito,Kunio Chikamori,Fusaji Sakurai |
| Vol. 12 | No. 2 | 1966 | Study on Electrolytic Machining Process (XI) -Effect of Inhibitor in Sodium Choloride Solution on the Surface Finish of Work Machined by a Single-Phase Half-Wave Rectified Current- |
Sukemitsu Ito,Nobuo Shikata |
| Vol. 12 | No. 2 | 1966 | Study on Fluid Logic Elements (III) -Flow Patterns in Flueric Biastable Element- |
Shotaro Ozaki,Yoshiaki Hara,Yohiyuki Shimazaki |
| Vol. 12 | No. 2 | 1966 | The Effect of Ageing Terms on Chemical Reaction between Powdered Brass and Stearic Acid | Takeshi Furusawa,Go Yaguchi,Kazuo Kato |
| Vol. 13 | No. 1 | 1967 | Study on the Pitting in Rolling Contact (I) -On the Mechanism of the Pitting Occurrence- |
Hisashi Miyoshi,Jun Takada |
| Vol. 13 | No. 1 | 1967 | Study on Electrolytic Machining Process (XII) -Corrosion of Mild Steel in Sodium Chloride Solution (II)- |
Sukemitsu Ito,Hideo Yamamoto,Kunio Chikamori |
| Vol. 13 | No. 1 | 1967 | Research on the Characteristics of the Mechanical System of Machine Tools (I) | Takeshi Yasui |
| Vol. 13 | No. 1 | 1967 | On the Automobile Test Dust (II) -Burning Methods for Raw Material of “Nos.7 and 8 Powders for Industrial Testing” in JIS Z8901- |
Ken-ichi Yamashita |
| Vol. 13 | No. 2 | 1967 | On the Vortex Flow in Suction Pipes | Masakazu Harada |
| Vol. 13 | No. 2 | 1967 | Study on Electrophoretic Deposition | Hideo Yamamoto,Sukemitsu Ito |
| Vol. 13 | No. 2 | 1967 | On the Location of the Center of Shear | Masayuki Ikui |
| Vol. 13 | No. 2 | 1967 | Characteristics of Guidance Cable for Automatic Steering Control | Shuntetsu Matsumoto,Shinzaburo Inomata,Yasuo Suzuki |
| Vol. 13 | No. 2 | 1967 | Optimal Offsets of a Mixed Offset Signal System in Road Traffic | Akira Takahashi,Chizuko Umezawa |
| Vol. 14 | No. 1 | 1968 | Rheological Aspect of Tool Wear in Machining Graphite | Hidehiko Takeyama,Takashi Ogino,Shinichi Miyazawa |
| Vol. 14 | No. 1 | 1968 | Basic Investigation of Built-Up-Edge | Hidehiko Takeyama,Tomohiko Ono |
| Vol. 14 | No. 1 | 1968 | Study on Electrolytic Honing | Terumi Murai,Keisaku Okano,Kazutaka Tamakohri,Hidehiko Takeyama,Tsuguya Sakashita |
| Vol. 14 | No. 1 | 1968 | On Wear Process of Grinding Wheel in Heave Grinding (I) | Hideichi Makino,Shozo Suzuki |
| Vol. 14 | No. 1 | 1968 | Experimental Studies of Arc-Heated, Low-Density Plasma Flow (I) | Iwao Yamashita,Tetsuo Yamanishi |
| Vol. 14 | No. 2 | 1968 | Automatic Control of Pure Integral Process with Dead-Time -An Application of Sampling Controller and a method for Adjusting Its Parameters- |
Tsunenori Honda,Kazuto Togino |
| Vol. 14 | No. 2 | 1968 | Sensors of Tool Life For Optimization of Machining | Hidehiko Takeyama,Yasuhiro Doi,Toyokazu Mitsuoka,Hiroshi Sekiguchi |
| Vol. 14 | No. 2 | 1968 | A Stduy on Determination of Insolubles in Used Lubricating Oils (I) -On Used Oil Insolubles for Several Solvenes- |
Takeshi Ishii,Isamu Shimada |
| Vol. 14 | No. 2 | 1968 | On the Acoustic Characteristics of the Anechoic Room | Motoichi Kitada,Hisao Sakurai |
| Vol. 14 | No. 2 | 1968 | Observation of Adhesion between Coated Film and Substrate by Means of X-ray Microanalyzer | Shigetake Okamoto |
| Vol. 14 | No. 2 | 1968 | Fan Noise (I) -Noise of Automotive Cooling Fans- |
Iku Harada |
| Vol. 14 | No. 2 | 1968 | Investigations on Externally Pressurized Air Journal Bearings (II) -Experimental Study on the Dynamic Instability- |
Masakazu Harada,Toshinori Ogawa |
| Vol. 15 | No. 1 | 1969 | Magnetohydrodynamic Slip Flow in the Entrance Region of a Parallel Plate Channel (I) | Kentaro Kikuchi |
| Vol. 15 | No. 1 | 1969 | Magnetohydrodynamic Slip Flow in the Entrance Region of a Parallel Plate Channel (II) | Kentaro Kikuchi |
| Vol. 15 | No. 1 | 1969 | Heat Transfer to MHD Slip Flow in the Thermal Entrance Region of a Parallel Plate Channel | Kentaro Kikuchi |
| Vol. 15 | No. 1 | 1969 | Electrode Processes in Electrochemical Machining (I) -Potentiodynamic Polarization Curves of Mild Steel in Sodium Chloride Solution- |
kunio Chikamori,Sukemitsu Ito |
| Vol. 15 | No. 1 | 1969 | An Approximate Method for Analysis of Stability and Step Response of the Nonlinear Second Order System with a Periodically Time-Varying Restoring-Force Term | Tsunenori Honda |
| Vol. 15 | No. 1 | 1969 | Comparison of Machinability between Home Made and OECD Calcium-Deoxidized Steel | Hidehiko Takeyama,Ryoji Murata,Tsutomu Yato,Urako Kiyono,Takeo Tomita |
| Vol. 15 | No. 1 | 1969 | Study on Establishment of Machining Standards (XI) -Machining Standards for Turning Annealed Low Carbon Steels(S15C and S25C)- |
Hidehiko Takeyama,Umetaro Kasuya,Hiroshi Sekiguchi,Toshitaka kuroume,Tsutomu Yato |
| Vol. 15 | No. 1 | 1969 | STUDY ON ESTABLISHMENT OF MACHINING STANDARDS (XII) -Machining Standards for Turning Normalized Medium Carbon Steels (S35C, S45C & S55C)- |
Hidehiko Takeyama,Tsutomu Yato,Umetaro Kasuya,Teiji Yoshikawa,Kaneyoshi Miyasaka |
| Vol. 15 | No. 1 | 1969 | STUDY ON ESTABLISHMENT OF MACHINING STANDARDS -Machining Standards for Turning Cast Steel (SC46) and High Manganese Cast Steel (annealed) (SCMnH2)- | Hidehiko Takeyama,Tsutomu Yato,Teiji Yoshikawa,Hiroshi Sekiguchi,Kazuichiro Kishimoto |
| Vol. 15 | No. 1 | 1969 | On the Sliding Friction Tester and Its Natural Frequency | Kiyoshi Matsubara,Makoto Watanabe |
| Vol. 15 | No. 1 | 1969 | Metallic Tracer Method Determining Lubricating Oil Consumption of Automotive Gasoline Engines (I) -A Newly Deeloped Additive- |
Isamu Shimada,Takeshi Ishii |
| Vol. 15 | No. 1 | 1969 | Characteristics of Course Deviation Detector for Automatic Steering Car | Shuntetsu Matsumoto,Shinzaburo Inomata,Yasuo Suzuki |
| Vol. 15 | No. 1 | 1969 | Collapse of Metal plates by High speed Liquid Jets | Kazuyoshi Fukuzawa,Mitsuyoshi Iguchi |
| Vol. 15 | No. 2 | 1969 | Analytical and Experimental Study of Water Freezing Process | kentaro Kikuchi |
| Vol. 15 | No. 2 | 1969 | Study on Electrolytic Machining Process (XIII) -Effect of the Wave Form of Machining Current on the Surface Finish- |
Sukemitsu Ito,Nobuo Shikata |
| Vol. 15 | No. 2 | 1969 | Study on Electrolytic Machining Process (XIV) -Corrosion of Cast Iron in Sodium Chloride Solution (1)- |
Sukemitsu Iot,Hideo Yamamoto |
| Vol. 15 | No. 2 | 1969 | The Frictional Properties of Nylon | Makoto Watanabe,Makoto Karasawa,Kiyoshi Matubara |
| Vol. 16 | No. 1 | 1970 | Application fo Ferromagnetic Thin Films to the Measurement of Mechanical Displacement part 1 | Yuzuru Watanabe,Shuntetsu Matsumoto |
| Vol. 16 | No. 1 | 1970 | Study on Ultrasonic Broaching | Hidehiko Takeyama,Umetaro Kasuya |
| Vol. 16 | No. 1 | 1970 | Analytische und experimentelle Untersuchung eines Hochspannungs-EGD-Generators | Kentaro Kikuchi,Kazuyoshi Fukuzawa |
| Vol. 16 | No. 1 | 1970 | Analogies of Vibration of Elastic Bars by Electrical Circuits -Fundamental Application- |
Shigeo Fujimoto,Tamotsu Sufu |
| Vol. 16 | No. 1 | 1970 | Analysis of Signal Control in Road Traffic -for One Intersection- |
Chizuko Umezawa,Akira Takahashi |
| Vol. 16 | No. 1 | 1970 | Combustion of Liquefied Petroleum Gas in Otto Engine | Hisashi Yasui |
| Vol. 16 | No. 1 | 1970 | Electrode Processes in Electrochemical Machining (II) -Potentiodynamic Polarization Curves of Mild Steel in Some Electrolytes for Electrochemical Machining- |
Kunio Chikamori,Sukemitsu Ito |
| Vol. 16 | No. 1 | 1970 | Study on Corrosion in Electrochemical Machining (I) -Corrosion of Mild Steel in Solution of Salts Including Halogens- |
Hideo Yamamoto,Sukemitsu Ito |
| Vol. 16 | No. 2 | 1970 | A New Method of Measuring the Rolling Bearing Chamfer | Junzo Okamoto,Shizuo Koizumi,Susumu Miyazaki |
| Vol. 16 | No. 2 | 1970 | Effects of Atmospheric Conditions on Automobile Emissions | Naohisa Teshirogi,Sadaichi Ozaki,Yoshitada Uchiyama |
| Vol. 16 | No. 2 | 1970 | Switching in Wall Attachment Device | Makoto Kimura |
| Vol. 16 | No. 2 | 1970 | A Concept of Program-Controlled Running of the Engine on the Dynamometer | Shigeru Yanagihara,Keizo Saito |
| Vol. 16 | No. 2 | 1970 | Passage Pattern Recognition for Safe Driving (I) -Information Processing Method- |
Taketoshi Nozaki,Shuntetsu Matsumoto,Teruo Yatabe,Kiichi Ikeda |
| Vol. 16 | No. 2 | 1970 | Study on Evaluation of Flux Cored Wires in CO2 Gas Arc Welding -Effect of Flow Rate of CO2 Gas on Mechanical Properties of Weld Metal and Formation of Bead- |
Kikuzo Ishiyama,Hideo Kobayashi |
